Spear

Spear

Spear rods are made for smaller substrates which have a through going hole like indexable cutting inserts. Cutting inserts e. g. are lined up on the spear rod with spacers in between them in order to provide defined distance between them. All spear rods have a gear close to the bottom end.

The size of the gear should be equal or bigger than the outer circle of the substrates. The diameter of the spear rod should be smaller (about 0,3mm) than the diameter of the hole. Rods in length of 250 mm and 300 mm can be ordered directly here in the shop. Each other length can be delivered upon inquiry.

As default the teeth of the gear face counter clockwise (CCW) for base plates which also rotate CCW. The rods themselves in this case will rotate CW. If your planets rotate clockwise (CW) please mention that the teeth shall face CW.


Display per page
Sort by
Product no.: 415550086

Square shaped rod for hook springs. Both ends reduced to Ø4,0mm, Total length free up to 500mm

55.00 *
Delivery weight: 68.467 g

On Stock: >

Product no.: 415550087

Hook spring made of 0,8mm spring steel (1.4310) to put on sqaure rods. 

5.00 *
Delivery weight: 0.567 g

On Stock: >

Product no.: 403941829

Rods with a ring gear at the lower end are suitable for holding substrates with a hole, such as indexable inserts. The ring gear has a diameter of approx. 15mm, so that substrates up to this outer circle diameter can be charged. Rod diameter and length can be selected through the variants. Rods with a diameter of bigger than 4.0mm are set off at both ends to 4.0mm. When ordering, please specify whether the teeth of the ring gear should point to the left or right.

Single Piece 12.80 *

On Stock: >

Product no.: 403941828

Rods with a ring gear at the lower end are suitable for holding substrates with a hole, such as indexable inserts. The ring gear has a diameter of approx. 11mm, so that substrates up to this outer circle diameter can be charged. Rod diameter and length can be selected through the variants. Rods with a diameter of bigger than 3.0mm are set off at both ends to 4.0mm. When ordering, please specify whether the teeth of the ring gear should point to the left or right.

Single Piece 8.00 *

On Stock: >

Product no.: 403941830

Rods with a ring gear at the lower end are suitable for holding substrates with a hole, such as indexable inserts. The ring gear has a diameter of approx. 18mm, so that substrates up to this outer circle diameter can be charged. Rod diameter and length can be selected through the variants. Rods with a diameter of smaler than 3.0mm run a little out of round in standard base plates. When ordering, please specify whether the teeth of the ring gear should point to the left or right.

Single Piece 6.40 *

On Stock: >

Product no.: 403941831

Rods with a ring gear at the lower end are suitable for holding substrates with a hole, such as indexable inserts. The ring gear has a diameter of approx. 18mm, so that substrates up to this outer circle diameter can be charged. Rod diameter and length can be selected through the variants. Rods with a diameter of bigger than 4.0mm are set off at both ends to 4.0mm. When ordering, please specify whether the teeth of the ring gear should point to the left or right.

Single Piece 12.80 *

On Stock: >

Product no.: 403941832

Rods with a ring gear at the lower end are suitable for holding substrates with a hole, such as indexable inserts. The ring gear has a diameter of approx. 24mm, so that substrates up to this outer circle diameter can be charged. Rod diameter and length can be selected through the variants. Rods with a diameter of smaller than 3.0mm run a little out of round in standard base plates. When ordering, please specify whether the teeth of the ring gear should point to the left or right.

Single Piece 6.40 *

On Stock: >

Product no.: 403941833

Rods with a ring gear at the lower end are suitable for holding substrates with a hole, such as indexable inserts. The ring gear has a diameter of approx. 24mm, so that substrates up to this outer circle diameter can be charged. Rod diameter and length can be selected through the variants. Rods with a diameter of bigger than 4.0mm are set off at both ends to 4.0mm. When ordering, please specify whether the teeth of the ring gear should point to the left or right.

Single Piece 12.80 *

On Stock: >

Product no.: 403941834

Rods with a ring gear at the lower end are suitable for holding substrates with a hole, such as indexable inserts. The ring gear has a diameter of approx. 32mm, so that substrates up to this outer circle diameter can be charged. Rod diameter and length can be selected through the variants. Rods with a diameter of smaller than 3.0mm run a little out of round in standard base plates. When ordering, please specify whether the teeth of the ring gear should point to the left or right.

Single Piece 6.40 *

On Stock: >

Product no.: 403941835

Rods with a ring gear at the lower end are suitable for holding substrates with a hole, such as indexable inserts. The ring gear has a diameter of approx. 32mm, so that substrates up to this outer circle diameter can be charged. Rod diameter and length can be selected through the variants. Rods with a diameter of bigger than 4.0mm are set off at both ends to 4.0mm. When ordering, please specify whether the teeth of the ring gear should point to the left or right.

Single Piece 12.80 *

On Stock: >

Product no.: 403941836

Rods with a ring gear at the lower end are suitable for holding substrates with a hole, such as indexable inserts. The ring gear has a diameter of approx. 40mm, so that substrates up to this outer circle diameter can be charged. Rod diameter and length can be selected through the variants. Rods with a diameter of smaller than 3.0mm run a little out of round in standard base plates. When ordering, please specify whether the teeth of the ring gear should point to the left or right.

Single Piece 6.40 *

On Stock: >

Product no.: 403941837

Rods with a ring gear at the lower end are suitable for holding substrates with a hole, such as indexable inserts. The ring gear has a diameter of approx. 41mm, so that substrates up to this outer circle diameter can be charged. Rod diameter and length can be selected through the variants. Rods with a diameter of bigger than 4.0mm are set off at both ends to 4.0mm. When ordering, please specify whether the teeth of the ring gear should point to the left or right.

Single Piece 12.80 *

On Stock: >

Product no.: 415554821
85.00 *
Delivery weight: 67.467 g

On Stock: >

*
Prices plus VAT, plus delivery

Spear Accessory

Spear Accessory

 

Slotted Pins adjust the space between cutting inserts. Rod Locker Springs secure the electrical contact.